Insulation in Palmdale, CA
Spray foam insulation in Palmdale has to contend with a thermal environment unlike anywhere else in Los Angeles County: summer attics that hit 150°F by noon and winter nights that drop into the low 20s. The 1980s and 90s tract homes that dominate Palmdale were built fast for aerospace workers during the Northrop and Lockheed boom, and most still carry their original builder-grade R-13 wall batts and R-19 attic batts. Those materials are now 30 to 40 years old, compressed, dusty, and working against a climate that demands far more from a building envelope than coastal contractors ever deal with. Call (661) 545-6966 to talk through what your Palmdale home actually needs.
Why Palmdale Homes Are Different
Palmdale sits at roughly 2,700 feet in the Antelope Valley high desert, which means an 80 to 90 degree seasonal swing every year. Your attic hits 150 to 160°F in July and the same roof faces pipe-freezing nights in December. That thermal stress cycle, repeated year after year, crushes compressed fiberglass batts and accelerates air leakage through every gap in the building envelope. Add in Antelope Valley winds and intense high-altitude solar radiation, and you have convective heat loss paths that standard coastal insulation jobs never expose.
The housing stock makes it worse. Palmdale’s dominant home type is the 1980s and 90s wood-frame tract build: ranch and two-story models with vaulted ceilings and hip roofs that create awkward attic geometries. Blown-in retrofits in these homes require working around angled framing, shallow soffit bays, and irregular top plates. And because Palmdale falls under CEC Climate Zone 14, Title 24 mandates an attic R-value of R-38 minimum, with R-49 often recommended. Homeowners moving up from the San Fernando Valley routinely assume their insulation needs are the same. They’re not. Permitted remodels frequently trigger mandatory attic upgrades that catch people off guard, and we regularly fix jobs where a previous contractor blew R-19 over old R-13 and called it done.
Our Main Palmdale Services
Most Palmdale homeowners call us first about the two parts of the home that leak the most energy and cause the most comfort problems: the attic and the crawl space.
Attic Insulation in Palmdale
In Palmdale’s climate zone, the attic is the single biggest driver of indoor temperature and cooling cost. We audit the attic first, check what’s actually up there, then recommend the right material for the roof geometry and duct layout, whether that’s blown-in fiberglass, cellulose, or spray foam. Vaulted ceilings and hip roofs common in Palmdale tract homes change how air moves across the attic floor, so the installation sequence matters as much as the material. See the full breakdown on our Attic Insulation in Palmdale page.
Crawl Space Encapsulation & Vapor Barrier in Palmdale
Palmdale gets cold enough every winter that uninsulated crawl spaces pull heat straight out of the floor, and windy springs push dust and moisture through foundation vents. Encapsulation seals the crawl space from the high-desert air, keeps ground moisture from rising into the floor framing, and stops the cold drafts that make tile and wood floors feel like ice in January. See what’s involved on our Crawl Space Encapsulation & Vapor Barrier in Palmdale page.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Spray Foam Insulation in Palmdale
Spray foam insulation in Palmdale is the highest-performing answer to the high-desert thermal swing, because it air-seals while it insulates. In a 1980s Palmdale tract home, the original fiberglass batts leave dozens of unsealed gaps around top plates, can lights, and duct boots, and that’s where the Antelope Valley wind finds its way in. Closed-cell foam stops that air movement at the source, and open-cell foam handles the vaulted and hip-roof geometries that make blown-in retrofits difficult. For a detailed look at how spray foam works, see our Spray Foam Insulation page.
Open-Cell Spray Foam
Signs you need it
Rooms that never hold temperature in summer, high cooling bills that don’t drop after a basic attic top-up, or visible gaps around can lights and top plates in older Palmdale homes.
What it costs in Palmdale
Expect $1.10 to $2.75 per board foot for open-cell foam in Palmdale attics and rim joists.
How we do it
We seal the attic access, prep the surfaces, then spray open-cell foam to the specified depth across the attic floor or roof deck, letting it expand into every seam before trimming and inspecting.
Closed-Cell Spray Foam
Signs you need it
You want maximum R-value per inch in a tight roof cavity, or you have moisture concerns in a vented attic that’s pulling in high-desert dust and humidity swings.
What it costs in Palmdale
Closed-cell spray foam runs $2.90 to $5.60 per board foot in Palmdale.
How we do it
We apply closed-cell foam in controlled lifts, typically on roof decks, rim joists, and crawl space walls, then check for full adhesion and trim any over-spray.
Garage Ceiling Spray Foam
Signs you need it
Bedrooms above a garage that roast in summer and freeze in winter, common in Palmdale two-story tract plans where the garage ceiling was never insulated properly.
What it costs in Palmdale
Garage ceiling spray foam typically lands between $1,400 and $2,900 depending on square footage and foam type.
How we do it
We mask and ventilate the garage, spray the ceiling cavity with the specified foam depth, then finish with a thermal boundary inspection.
What Spray Foam Insulation Costs in Palmdale
| Item | Typical range in Palmdale |
|---|---|
| Open-cell spray foam (attic) | $1.10–$2.75 per board foot |
| Closed-cell spray foam (attic) | $2.90–$5.60 per board foot |
| Garage ceiling spray foam | $1,400–$2,900 |
| Spray foam roof deck | $5,500–$12,000+ |
Does spray foam work in Palmdale’s high heat?
Yes. Closed-cell and open-cell foam both hold R-value in extreme heat, unlike fiberglass batts which lose effectiveness as attic temperatures climb past 140°F. Foam also air-seals the gaps the Antelope Valley wind exploits. Call (661) 545-6966 for a free estimate on your Palmdale home.
Can you spray foam a vaulted ceiling in an older Palmdale home?
Yes, and it’s often the best option. Vaulted and hip-roof geometries leave little room for blown-in material, but open-cell foam conforms to irregular cavities. The owner handles the assessment personally, so the recommendation fits your actual roof framing, not a generic plan.
Blown-In Insulation in Palmdale
Blown-in insulation in Palmdale is the most practical retrofit for the thousands of 1980s and 90s tract homes still running on original R-19 attic batts. When those batts compress under decades of thermal cycling from 20°F winters to 150°F attics, they lose R-value and leave gaps along the top plates. Blown-in material fills those voids and brings the attic up to the R-38 minimum (and usually R-49) that CEC Climate Zone 14 requires. Learn more about the materials on our Blown-In Insulation page.
Blown-In Fiberglass
Signs you need it
Your attic has old, compacted yellow or pink batts that measure well below R-38, or you can see bare spots between the joists where the original install settled.
What it costs in Palmdale
Blown-in fiberglass in Palmdale attics runs $1.50 to $3.00 per square foot.
How we do it
We seal bypass gaps first, then blow fiberglass to the specified depth across the attic floor, working around ducts, vents, and framing without burying can lights.
Blown-In Top-Up
Signs you need it
You already have some attic insulation but energy bills are rising and you’re not sure if the depth meets current Palmdale code minimums.
What it costs in Palmdale
A blown-in top-up over existing insulation costs $1.00 to $2.25 per square foot in Palmdale.
How we do it
We measure existing depth, assess the condition of the old material, then blow the new layer to the target R-value with even coverage across every bay.
What Blown-In Insulation Costs in Palmdale
| Item | Typical range in Palmdale |
|---|---|
| Blown-in fiberglass (attic) | $1.50–$3.00 per sq ft |
| Blown-in cellulose (attic) | $1.30–$2.80 per sq ft |
| Dense-pack wall insulation | $2.50–$5.00 per sq ft |
| Blown-in top-up over existing | $1.00–$2.25 per sq ft |
How much attic insulation does Palmdale code actually require?
Palmdale falls under CEC Climate Zone 14, which requires R-38 minimum in attics, with R-49 recommended for new work. Most 1980s and 90s original builds sit at R-19 or less. A top-up closes that gap. Call (661) 545-6966 for an exact measurement and quote, free of charge.
Can you blow insulation without removing the old batts?
Sometimes. If the old batts are dry, clean, and not compressed beyond usefulness, we can blow on top. If they’re rodent-soiled, moisture-damaged, or heavily broken down, removal first protects the new layer’s performance.
Radiant Barrier Installation in Palmdale
Radiant barrier installation in Palmdale attacks the one thing no bulk insulation can stop: radiant heat gain from the sun hammering the roof deck for 12-plus hours on July days. When your attic hits 150°F, the roof deck is radiating heat downward into whatever insulation sits below it, and a radiant barrier reflects that energy back up before it ever reaches the living space. In Palmdale’s high-desert sun, that single layer can cut attic temperatures by 20 to 30 degrees. See the installation options on our Radiant Barrier Installation page.
Attic Radiant Barrier
Signs you need it
Your air conditioner runs constantly in August, the upstairs stays 8 to 10 degrees hotter than downstairs, or you can feel heat radiating through the ceiling late in the evening.
What it costs in Palmdale
Attic radiant barrier in Palmdale runs $1.50 to $3.50 per square foot installed.
How we do it
We staple the foil-faced barrier to the underside of the roof rafters, leaving the required air gap at the ridge and eave vents, then verify the reflective surface faces the correct direction.
Radiant Barrier & Ventilation
Signs you need it
Your attic has inadequate ridge or soffit venting, and the radiant barrier alone won’t solve the heat buildup because there’s nowhere for the hot air to go.
What it costs in Palmdale
Combined radiant barrier and ventilation upgrades in Palmdale typically cost $4.50 to $8.00 per square foot.
How we do it
We assess the existing venting, install or expand ridge and soffit vents as needed, then hang the radiant barrier so airflow moves heat out instead of trapping it against the roof deck.
What Radiant Barrier Installation Costs in Palmdale
| Item | Typical range in Palmdale |
|---|---|
| Attic radiant barrier (rafter-mounted) | $1.50–$3.50 per sq ft |
| Radiant barrier foil (material only) | $0.30–$0.80 per sq ft |
| Radiant barrier on roof deck | $2.00–$4.50 per sq ft |
| Radiant barrier + ventilation upgrade | $4.50–$8.00 per sq ft |
Does radiant barrier alone cool a Palmdale attic enough?
It helps significantly, but it’s not a standalone fix. A radiant barrier reduces radiant heat gain, while air sealing and adequate insulation handle conductive and convective losses. In Palmdale’s climate, all three layers work together. Call (661) 545-6966 to see what your attic actually needs.
Will a radiant barrier make my winter heating bill worse?
No. The barrier reflects radiant heat out in summer and reflects a small amount of interior heat back down in winter, but the net effect in Palmdale’s cooling-dominated climate is strongly positive. Winter heat loss through the attic is driven primarily by convection and conduction, not radiation.
Insulation Removal & Replacement in Palmdale
Insulation removal and replacement in Palmdale is a job most homeowners don’t realize they need until an energy audit or a mid-summer heat wave exposes the problem. After 30 to 40 years of high-desert thermal cycling, the original fiberglass batts in Palmdale tract homes are often compressed, dusty, and no longer performing anywhere near their labeled R-value. Sometimes they’re also contaminated by rodent activity, roof leaks, or blown-in desert dust. See the full removal process on our Insulation Removal & Replacement page.
Attic Insulation Removal
Signs you need it
Your attic insulation is visibly matted, compacted to half its original depth, or coated in dust and debris from decades of Antelope Valley wind infiltration.
What it costs in Palmdale
Attic insulation removal in Palmdale runs $1.50 to $3.50 per square foot.
How we do it
We run a commercial vacuum line from the attic to a containment bag outside, remove the old material down to the decking, then inspect the framing and wiring before any new insulation goes in.
Contaminated Insulation Removal
Signs you need it
You’ve had rodents, roof leaks, or pest activity in the attic, and the existing insulation shows droppings, staining, or embedded nesting material.
What it costs in Palmdale
Contaminated insulation removal in Palmdale adds a bio-sanitation step and runs $2.50 to $5.00 per square foot.
How we do it
We remove the contaminated material in sealed bags, sanitize the attic surfaces, and only then install fresh insulation over a clean, decontaminated substrate.
What Insulation Removal & Replacement Costs in Palmdale
| Item | Typical range in Palmdale |
|---|---|
| Attic insulation removal | $1.50–$3.50 per sq ft |
| Contaminated insulation removal | $2.50–$5.00 per sq ft |
| Insulation replacement (attic) | $2.50–$6.00 per sq ft |
| Vermiculite & old insulation removal | $4.00–$8.00 per sq ft |
Do I have to remove old insulation before adding new?
Not always. If the existing material is dry, clean, and not compressed beyond recovery, we can blow on top. If it’s rodent-soiled, water-damaged, or so broken down that it no longer holds air, removal is the only way to get a clean thermal boundary. Call (661) 545-6966 and we’ll assess it in person.
How long does attic insulation removal take in Palmdale?
Most Palmdale attics take one full day from start to clean inspection, depending on attic size and access. Hip-roof homes with tight eaves can add a few hours because the vacuum line has to reach every corner.
Attic Air Sealing in Palmdale
Attic air sealing in Palmdale is the step most insulation contractors skip, and it’s the step that matters most in a high-desert climate where wind and pressure differences push hot air in and cooled air out. Every gap around a can light, top plate, duct boot, or attic hatch is a direct leak path between your living space and a 150°F attic in July. Sealing those gaps first means the new insulation actually performs to its rated R-value. See the full scope on our Attic Air Sealing page.
Top Plate & Penetration Sealing
Signs you need it
You see dust streaks along ceiling joists, feel drafts near interior walls in windy months, or your energy bill climbs every time the Antelope Valley wind picks up.
What it costs in Palmdale
Top plate and penetration sealing in Palmdale runs $1.50 to $3.00 per linear foot of wall top plate.
How we do it
We pull back the attic insulation along each top plate, seal the drywall-to-framing seams with foam or caulk, then re-cover the area to the correct depth.
Can Light & Duct Boot Sealing
Signs you need it
You can feel air moving around recessed lights when the AC runs, or the upstairs is always several degrees off from the thermostat setting.
What it costs in Palmdale
Can light and duct boot sealing in Palmdale runs $50 to $150 per light or boot, depending on accessibility.
How we do it
We install rated covers or seal boxes around each fixture and duct boot, then test the connection with a smoke pencil to confirm the leak is closed.
What Attic Air Sealing Costs in Palmdale
| Item | Typical range in Palmdale |
|---|---|
| Attic floor air sealing | $1.50–$3.00 per sq ft |
| Top plate & penetration sealing | $1.50–$3.00 per linear ft |
| Can light & duct boot sealing | $50–$150 per fixture |
| Attic hatch sealing | $150–$400 per hatch |
Does air sealing really matter in Palmdale where it’s dry?
Yes, arguably more than on the coast. Palmdale’s extreme temperature swing and strong winds create bigger pressure differences across the building envelope, which means more air moves through every gap. Dry air still carries heat. Call (661) 545-6966 for a blower-door test and see exactly how much leakage your home has.
Can you air seal without removing the existing insulation?
In most cases we work around the existing material, pulling it back in sections, sealing the leaks, then redressing it to the correct depth. If the insulation is contaminated or heavily compressed, removal and replacement gives a cleaner result.
Wall Insulation in Palmdale
Wall insulation in Palmdale matters because those 1980s and 90s tract builds came with R-13 batts that were installed quickly, often poorly, and are now doing almost nothing in the wall cavities where the high-desert wind finds every seam. Winter nights in the low 20s pull heat straight through under-insulated walls, and summer afternoons push it back in. Retrofit wall insulation is the fix most Palmdale homeowners haven’t considered because the walls look fine from the outside. See the methods on our Wall Insulation page.
Injection Foam Wall Insulation
Signs you need it
Exterior walls feel cold to the touch in winter, heat radiates through them during July afternoons, or rooms along the west side of the house are always warmer.
What it costs in Palmdale
Injection foam wall insulation in Palmdale runs $2.50 to $5.00 per square foot of wall area.
How we do it
We drill small access holes through the drywall or stucco, inject the foam into each stud bay under controlled pressure, then patch the holes to match the surface.
Drill & Fill Wall Insulation
Signs you need it
Your home has cavities that were never insulated, or the original batts have slumped inside the walls, leaving gaps at the top of each cavity.
What it costs in Palmdale
Drill and fill wall insulation in Palmdale runs $2.00 to $4.50 per square foot.
How we do it
We drill a small hole at each stud bay, fill the cavity with blown-in fiberglass or cellulose, then restore the wall surface to a finished condition.
What Wall Insulation Costs in Palmdale
| Item | Typical range in Palmdale |
|---|---|
| Injection foam wall insulation | $2.50–$5.00 per sq ft |
| Drill & fill wall insulation | $2.00–$4.50 per sq ft |
| Exterior wall insulation (new build) | $1.50–$3.50 per sq ft |
| Interior wall soundproofing | $2.00–$4.00 per sq ft |
Can you insulate walls without tearing out drywall?
Yes. Injection foam and drill-and-fill methods use small access holes that we patch afterward, so the finished wall surface stays intact. Most Palmdale wall retrofits are done this way, and the whole job usually takes one to two days. Call (661) 545-6966 for a wall-by-wall assessment.
How do I know if my Palmdale walls have insulation?
Most 1980s and 90s Palmdale tract homes have R-13 batts, but quality varies widely. A thermal imaging scan during an energy audit shows exactly where the batts have slumped or where cavities were missed.
Attic Cleaning & Rodent Proofing in Palmdale
Attic cleaning and rodent proofing in Palmdale comes before new insulation, not after, because Palmdale’s desert-adjacent location means mice, rats, and pack rats find their way into attic spaces every fall when nighttime temperatures drop. Once they’re in, they soil the insulation, chew wiring, and build nests in the warmest spots near ducts and can lights. Cleaning first, then sealing every entry point, then installing fresh insulation is the only sequence that protects the investment. See the full process on our Attic Cleaning & Rodent Proofing page.
Attic Cleanout
Signs you need it
You hear scratching or movement above the ceiling at night, find droppings near the attic hatch, or see nesting material mixed into the existing insulation.
What it costs in Palmdale
Attic cleanout in Palmdale runs $600 to $1,800 depending on attic size and contamination level.
How we do it
We remove all contaminated material, vacuum the decking, and document every entry point before any exclusion work or new insulation begins.
Rodent Proofing & Exclusion
Signs you need it
You’ve had repeat rodent problems despite trapping, or you see daylight around roof vents, gable ends, or utility penetrations from inside the attic.
What it costs in Palmdale
Rodent proofing and exclusion in Palmdale runs $500 to $2,000 depending on how many entry points need to be sealed.
How we do it
We identify every access point from inside and outside, seal gaps with steel mesh and foam, install vent covers where needed, and verify the attic is closed before adding insulation.
What Attic Cleaning & Rodent Proofing Costs in Palmdale
| Item | Typical range in Palmdale |
|---|---|
| Attic cleanout | $600–$1,800 |
| Attic sanitizing & decontamination | $400–$1,200 |
| Rodent proofing & exclusion | $500–$2,000 |
| Attic restoration (clean, seal, insulate) | $2,500–$6,000+ |
Do I need attic cleaning before new insulation in Palmdale?
If there’s any sign of rodent activity, moisture, or heavy dust accumulation, yes. Installing new insulation over contaminated material seals the problem in and shortens the life of the new layer. Call (661) 545-6966 and we’ll inspect the attic before recommending anything.
How do rodents get into Palmdale attics?
Gable vents, roof vents without screens, utility penetrations, gaps at the fascia, and stucco cracks. The Antelope Valley’s temperature swings push rodents indoors every fall, and once they’re in, they follow the warmest paths near ducts and heat sources.
Home Energy Audit in Palmdale
A home energy audit in Palmdale is the diagnostic step that tells you where your money is actually going, instead of guessing at it. In a climate with an 80 to 90 degree seasonal swing, the answer is never one single thing: it’s a combination of air leakage, degraded insulation, duct loss, and solar gain through the roof. We test the whole house, not just the attic, and the report tells you which fixes will pay back fastest. See the full audit scope on our Home Energy Audit page.
Blower Door Test
Signs you need it
You feel drafts in winter despite closing every window, or your AC bill stays high even after adding insulation and sealing obvious gaps.
What it costs in Palmdale
A blower door test in Palmdale runs $200 to $600 as part of a full home energy audit.
How we do it
We mount the blower door in an exterior door frame, depressurize the house, and measure total air leakage in CFM, then locate the biggest leaks with a smoke pencil and thermal camera.
Thermal Imaging Inspection
Signs you need it
You have hot or cold spots in specific rooms, or you suspect missing or slumped insulation in the walls but don’t want to cut into drywall.
What it costs in Palmdale
Thermal imaging inspection in Palmdale runs $150 to $400 for the whole-home scan.
How we do it
We scan every wall, ceiling, and floor with an infrared camera, reading temperature differences that reveal insulation gaps, air leaks, and moisture intrusion without opening any surface.
What Home Energy Audit Costs in Palmdale
| Item | Typical range in Palmdale |
|---|---|
| Full home energy audit | $400–$900 |
| Blower door test (standalone) | $200–$600 |
| Thermal imaging inspection | $150–$400 |
| Duct leakage test | $150–$350 |
Is a home energy audit worth it in Palmdale?
Yes, especially in a 30 or 40-year-old Palmdale home. You’ll get a measured answer to which problems are actually costing you money, so you don’t spend on the wrong fix. Most audit fees can be applied toward the work that follows. Call (661) 545-6966 to schedule one.
How long does a Palmdale home energy audit take?
A full audit with blower door, thermal imaging, insulation inspection, and duct testing takes about 2 to 3 hours in a typical Palmdale ranch or two-story home. You’ll have a written report the same day.
Brands We Service in Palmdale
Prime Insulation Lancaster stocks and installs material from our brands including Owens Corning, Rockwool, and Johns Manville, sourced locally where possible. If a specific product line fits your Palmdale home better than what we carry, we can special-order it within a week in most cases.
Pricing for Insulation in Palmdale, CA
| Service | Typical range in Palmdale |
|---|---|
| Spray foam insulation (attic) | $1.10–$5.60 per board foot |
| Blown-in insulation (attic) | $1.30–$3.00 per sq ft |
| Radiant barrier installation | $1.50–$3.50 per sq ft |
| Insulation removal | $1.50–$5.00 per sq ft |
| Attic air sealing | $1.50–$3.00 per sq ft |
| Wall insulation (injection foam) | $2.50–$5.00 per sq ft |
| Attic cleaning & rodent proofing | $500–$2,000 per project |
| Home energy audit | $400–$900 |
| Crawl space encapsulation | $3,000–$9,000+ |
| Attic insulation in Palmdale | $1.50–$3.00 per sq ft |
In Palmdale, the biggest price movers are attic geometry (vaulted ceilings and hip roofs add labor), the condition of existing material if removal is required, and whether rodent exclusion is needed before new insulation goes in. Every quote is line-item upfront, and the number we give you is the number you pay.
Neighborhoods We Serve in Palmdale
We work across Palmdale’s tract-home neighborhoods every week, and our crew knows the roof and attic patterns in each one.
- Ana Verde
- Rancho Vista
- Desert Sahara
- Tradewinds
- Joshua Hills
Our usual response time in Palmdale is one to three days for a site visit, and same-week installation is common when materials are in stock.
Service Area — Cities Near Palmdale
Beyond Palmdale, Prime Insulation Lancaster serves the surrounding Antelope Valley and northern Los Angeles County communities. We regularly work in Lancaster, CA where our shop is based, as well as Acton, CA, Littlerock, CA, and San Fernando, CA for homeowners who need the same diagnostic-first approach across the wider area.
Serving Palmdale, CA — Our Local Coverage Area
We’re based in the Palmdale area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Insulation in Palmdale
We schedule Palmdale site visits within one to three days, and same-week installation is common for attic insulation, blown-in top-ups, and air sealing when materials are on hand. Spray foam and crawl space encapsulation typically take a little longer to schedule. Call (661) 545-6966 and we’ll give you a firm date.
Most insulation retrofits don’t require a permit in Palmdale, but if your project is part of a larger remodel that’s already permitted, Title 24 upgrades often trigger mandatory attic insulation minimums. We’ll tell you what applies to your specific job before any work starts.
Can you match Palmdale HOA requirements for attic access or exterior work?
We work with HOAs throughout Palmdale and coordinate exterior work like vent replacement or crawl space access to meet architectural requirements. Our owner handles the assessment and stays on-site through completion
What happens when you call
- 1A real person answersNo phone trees — talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically same-day.
- 4You approve before work beginsNothing starts until you say go.
What Palmdale Customers Say
"Installed baffles at the soffits so the new insulation didn't block the ventilation, which the previous contractor apparently never considered."
— Eduardo Garcia"He did a blower door test before and after and gave me the numbers. I like being able to see the difference rather than being told about it."
— Renee Parker"Found and sealed a gap around the chimney chase that was basically an open chimney to the attic."
— Karen Park